Přeinstalace windows 7
Dobrý den, potřebuju přeinstalovat windows 7 a nedaří se mi dostat do boot menu abych nastavil bootovani z flash disku... Mám notebook Acer 5742Z
Dobrý den, potřebuju přeinstalovat windows 7 a nedaří se mi dostat do boot menu abych nastavil bootovani z flash disku... Mám notebook Acer 5742Z
Předmět | Autor | Datum |
---|---|---|
F12 Wikan 15.04.2012 17:56 |
Wikan | |
při držení klavésy F12 notebook píská... z repráku...:( a nic nenajede... Pitris300 15.04.2012 17:59 |
Pitris300 | |
Klávesu nedržet, ale ťukat do ní. A možná to není F12, ale jiná (nutno vyzkoušet, v nejvyšší nouzi s… Pytlík 15.04.2012 18:07 |
Pytlík | |
Je nutné přeinstalovat? Není na notebooku recovery oddíl? Vložíš Flash disk do USB, zapneš počítač a… nononot 15.04.2012 18:00 |
nononot | |
právě že není... a v biosu nejde změnit prioritu výběru bootování Pitris300 15.04.2012 18:02 |
Pitris300 | |
To activate the BIOS Utility, press F2 during POST (when “Press <F2> to enter Setup” message is prom… nononot 15.04.2012 18:08 |
nononot | |
Díky moc nemohl jsem to najít, já na svojem PC mám právě úplně jiný BIOS tak jsem to nemohl najít..… poslední Pitris300 15.04.2012 18:11 |
Pitris300 |
Zpět do poradny Odpovědět na původní otázku Nahoru
F12
při držení klavésy F12 notebook píská... z repráku...:( a nic nenajede...
Klávesu nedržet, ale ťukat do ní. A možná to není F12, ale jiná (nutno vyzkoušet, v nejvyšší nouzi se pak poradit s manuálem...)
Je nutné přeinstalovat? Není na notebooku recovery oddíl? Vložíš Flash disk do USB, zapneš počítač a po startu zmáčkneš klávesu...
právě že není... a v biosu nejde změnit prioritu výběru bootování
To activate the BIOS Utility, press F2 during POST (when “Press <F2> to enter Setup” message is prompted
on the bottom of screen).
The default parameter of F12 Boot Menu is set to “disabled”. If you want to change boot device without
entering BIOS Setup Utility, please set the parameter to “enabled”.
Press <F12> during POST to enter multi-boot menu. In this menu, user can change boot device without
entering BIOS SETUP Utility.
Navigating the BIOS Utility
There are five menu options: Information, Main, Security, Boot, and Exit.
Follow these instructions:
• To choose a menu, use the left and right arrow keys.
• To choose an item, use the up and down arrow keys.
• To change the value of a parameter, press F5 or F6.
• Press Esc while you are in any of the menu options to go to the Exit menu.
•
In any menu, you can load default settings by pressing F9. You can also press F10 to save any
changes made and exit the BIOS Setup Utility.
NOTE: You can change the value of a parameter if it is enclosed in square brackets.
Díky moc nemohl jsem to najít, já na svojem PC mám právě úplně jiný BIOS tak jsem to nemohl najít.. Téma vyřešeno