Přidat otázku mezi oblíbenéZasílat nové odpovědi e-mailem Usporný režim na HDD

>tlačítko přestalo fungovat- to znamená, že nejde ani vypnout ani zapnout

nevíte někdo přesně, které volby přímo určují ten idle timeout? Případně jak to funguje? TO se jen zapíše určitá hodnota do disku a on si to řídí sám?

volba -B (APM) říká, že hodnota pod 127 dovolí zastavení ploten.


z návodu hdparm znám tyto volby:

 -B     Get/set Advanced Power Management feature, if the drive supports it. A low value means aggressive power management and a  high  value  means
              better  performance.   Possible  settings range from values 1 through 127 (which permit spin-down), and values 128 through 254 (which do not
              permit spin-down).  The highest degree of power management is attained with a setting of 1, and the highest I/O performance with  a  setting
              of  254.  A value of 255 tells hdparm to disable Advanced Power Management altogether on the drive (not all drives support disabling it, but
              most do)

-M     Get/set Automatic Acoustic Management (AAM) setting. Most modern harddisk drives have the ability to speed down the head movements to reduce
              their noise output.  The possible values are between 0 and 254. 128 is the most quiet (and therefore slowest) setting and  254  the  fastest
              (and  loudest). Some drives have only two levels (quiet / fast), while others may have different levels between 128 and 254.  At the moment,
              most drives only support 3 options, off, quiet, and fast.  These have been assigned the values 0, 128, and 254 at present, respectively, but
              integer space has been incorporated for future expansion, should this change.
U některých gui nástrojů jsou volby quiet, fast a off. Co znamená off(jaký je to extrém)?


Další volby jsou jaksi specifické a nefungujejí např. ani v SATA boxech:
-Z     Disable the automatic power-saving function of certain Seagate drives (ST3xxx models?), to prevent them from idling/spinning-down at  incon‐
              venient times.
-S     Put the drive into idle (low-power) mode, and also set the standby (spindown) timeout for the drive.  This timeout  value  is  used  by  the
              drive  to  determine how long to wait (with no disk activity) before turning off the spindle motor to save power.  Under such circumstances,
              the drive may take as long as 30 seconds to respond to a subsequent disk access, though most drives are much quicker.  The encoding  of  the
              timeout  value  is  somewhat peculiar.  A value of zero means "timeouts are disabled": the device will not automatically enter standby mode.
              Values from 1 to 240 specify multiples of 5 seconds, yielding timeouts from 5 seconds to 20 minutes.  Values from 241 to 251 specify from  1
              to 11 units of 30 minutes, yielding timeouts from 30 minutes to 5.5 hours.  A value of 252 signifies a timeout of 21 minutes. A value of 253
              sets a vendor-defined timeout period between 8 and 12 hours, and the value 254 is reserved.  255 is interpreted as 21 minutes plus  15  sec‐
              onds.  Note that some older drives may have very different interpretations of these values.
Je volba -S ta hlavní, když se mluví o době uspání disku?


A ještě se chci zeptat, spíš objasnit, jaké stupně "šetření" má ten hardisk:

dočasné zpomalení hlav (AAM) - spíš jde o provozní vlastnost
zaparkování hlav (to dělá jaký příkaz)
zastavení ploten (to realizuji volbou -Y)
je tam ještě něco?

jak se těmto režimům říká? v návodu jsou zminována slova idle, lowpower, standby.

a ještě jak se liší příkazy --idle-imediate a --idle-unload


Jako třešnička na dortu: Mám disk Seagate freeagent, který se po nezjištěné době (do 15 minut určitě zastaví), nevím jak to vypnout na linuxu? (volby -Z a -S to neovlivní i když disk byl připojen přes box, který ty ATa PŘÍKAZY uměl)

Reakce na odpověď

1 Zadajte svou přezdívku:
2 Napište svou odpověď:
3 Pokud chcete dostat ban, zadejte libovolný text:

Zpět do poradny